Glossary

In our ESD Glossary we offer you an abundance of technical explanations of terms and standards used in the exciting world of the electronics industry. Whether you are an experienced expert or just starting out in this exciting industry, this glossary will help you to understand the meaning and context of important terms. From basics like electrostatic charge and resistors to ESD models, we will help you to keep track of things. In addition, we will look at relevant norms and standards that are widely used in the electronics industry. Immerse yourself in the world of the electronics glossary and expand your knowledge of this dynamic industry.



Terms

Bleeder resistance The bleeder resistance is the resistance between an electrode on the top of a device and the ESD grounding point. The resistance to ground is the resistance between an electrode on the top of a device and the ground potential.
 
Discharge time The time interval in which a charged body is discharged from an initial value to a final value by the connection to the ground potential, e.g. from 1000V to 100V.
 
CDM The Charged Device Model describes the mechanisms that occur when a charged component is discharged. The electrostatic sensitivity is determined by a pulse defined by the equivalent circuit.
 
Conductive Are materials having a surface resistance greater than 102 ohms and less than 105 Ohm (according to DIN EN 61340-5-1)
 
Dissipative Are materials having a surface resistance greater than 105 ohms and less than 1011 Ohm (according to DIN EN 61340-5-1)
 
EBP Earth Bonding Point is the marked connection for all ESD grounding measures; it must not be used as a protective conductor.
 
EPA The Electrostatic Protected Area is an area equipped with ESD protection measures where ESDS can be manufactured, processed, packaged, transported or stored without the risk of electrostatic damage.
 
ESD Electrostatic discharge is the electrostatic discharge used as equipotential bonding between charged bodies by direct contact or flashover.
 
ESD models Using idealized model ideas, an attempt is made to simulate real ESD discharges and to define test methods for determining the device sensitivity. The most important models are HBM, CDM and MM.
 
ESDS Electrostatic Discharge Sensitive Device:
Designation for components or assemblies that are caused by electrostatic discharges during handling, processing or transport.
 
ESD voltage sensitivity Damage threshold of a device to certain discharge pulses of the discharge models HBM, CDM or MM.
 
Electrostatic charge In physics, this term refers to idle electrical charges generated by mechanical contact and subsequent separation of materials.
 
HBM The Human Body Model describes the mechanisms that occur when a charged human body is discharged via a component or assembly. The electrostatic sensitivity is determined by a pulse defined by the equivalent circuit.
 
Ionization Positive and negative ions generated by the corona effect under high voltage neutralize electrostatic charges. They are mainly used for discharging non-conductors.
 
Insulator Materials having a surface resistance greater than 1011 Ohm are insulating.
 
Low Charging Materials are weakly chargeable if they have the property of not charging or only insignificantly charging on contact and subsequent separation or friction.
 
MM The machine model describes the mechanisms that occur during the discharge of a charged machine or plant component. The electrostatic sensitivity is determined by a pulse defined by the equivalent circuit.
 
Surface resistance The surface resistance of a material is the electrical resistance between two electrodes placed on the surface. For comparative measurements, the distance between the electrodes must be indicated.
 
Potential equalization Electrostatic charges must be immediately compensated against ground potential (0V) without danger to ESDS. The primary objective of ESD protection is to prevent the occurrence static charges.
 
Volume resistance In case a material is made entirely of conductive material, the current essentially flows through the body of the material. The resistance is measured between an electrode on the top and a counter electrode on the opposite point on the lower surface of the material.
 
Volume conductivity Characterizes materials by the fact that the entire material is dissipative, and not just the surface.
 
 


Terms

DIN-Notation VDE-Notation As of Standard contents
DIN IEC/TR 61340-1 VDE 0300-1 2021-08 Electrostatics – Part 1: Electrostatic processes - Fundamentals and measurements – (IEC/TR 61340-1:2012 + Cor1:2013 + COR2:2017 + AMD1:2020)
DIN EN 61340-2-1 VDE 0300-2-1 2016-07 Electrostatics – Part 2-1: Measurement methods – Ability of materials and products to dissipate electrostatic charges – (IEC 61340-2-1:2015)
DIN EN 61340-2-3 VDE 0300-2-3 2017-05 Electrostatics – Test methods for the determination of the resistance and resistivity of solid flat materials used to avoid electrostatic charge – (IEC 61340-2-3:2000)
DIN EN 61340-4-1 VDE 0300-4-1 2016-04 Electrostatics – Part 4-1: Standard test methods for special applications – Electrical resistance of floor coverings and installed floors – (IEC 61340-4-1:2003 + A1:2015)
DIN IEC/TS 61340-4-2 VDE V 0300-4-2 2016-01 Electrostatics – Part 4-2: Standard test methods for special applications – Electrostatic properties of textiles (IEC/TS 61340-4-2:2013)
DIN EN 61340-4-3 VDE 0300-4-3 2018-10 Electrostatics – Standard test methods for special applications – Footwear – (IEC 61340-4-3:2001)
DIN EN 61340-4-4 VDE 0300-4-4 2015-11 Electrostatics – Part 4-4: Standard test methods for special applications – Classification of flexible bulk solids containers (FIBC) in electrostatic terms – (IEC 61340-4-4:2012 + A1:2014)
DIN EN 61340-4-5 VDE 0300-4-5 2019-04 Electrostatics – Part 4-5: Standard test methods for special applications – Methods for characterizing the electrostatic protective effect of footwear and floor in combination with a person – (IEC 61340-4-5:2004)
DIN EN 61340-4-6 VDE 0300-4-6 2016-04 Electrostatics – Part 4-6: Standard test methods for special applications – Wrist straps – (IEC 61340-4-6:2015)
DIN EN 61340-4-7 VDE 0300-4-7 2018-01 Electrostatics - Part 4-7: Standard test methods for special applications - Ionization - (IEC 61340-4-7:2017)
DIN EN 61340-4-8 VDE 0300-4-8 2015-08 Electrostatics – Part 4-8: Standard test methods for special applications – Shielding against electrostatic discharge – Bags – (IEC 61340-4-8:2014)
DIN EN 61340-4-9 VDE 0300-4-9 2020-06 Electrostatics – Part 4-9: Standard test methods for special applications – Shielding against electrostatic discharge – Clothing – (IEC 61340-4-9:2016)
DIN EN 61340-5-1 VDE 0300-5-1 Beiblatt 1 2017-01 Electrostatics – Part 5-1: Protection of electronic components against electrostatic phenomena – General requirements – (IEC 61340-5-1:2016
DIN EN 61340-5-2 VDE 0300-5-2 2019-04 Electrostatics – Part 5-2: Protection of electronic components against electrostatic phenomena – User manual – (IEC TR 61340-5-1:2018)
DIN EN 61340-5-3 VDE 0300-5-3 2016-04 Electrostatics – Part 5-3: Protection of electronic components against electrostatic phenomena – Properties and requirements for the classification of packaging used for components sensitive to electrostatic discharges – (IEC 61340-5-3:2015)